Aspöck ECOLED II rear lamps are available in several left and right hand versions with different connector layouts. Two lamps can look almost identical from the front while using different 7-pin connections, auxiliary 2-pin outputs or accessory combinations. For a distributor or workshop, the safest method is to identify the complete Aspöck part number and connector family before ordering.
This guide explains the practical differences between ASS2, AMP, 7-pin and 2-pin ECOLED II connections. Browse our ASPÖCK trailer lighting range, ASPÖCK rear lamps and end-outline marker lamps for related references.
Why the complete ECOLED II reference matters
Aspöck's catalogues list ECOLED II variants by side, voltage, connector type and auxiliary-output configuration. The manufacturer also distinguishes lamp versions that include four additional 2-pin connections and versions supplied for different end-outline marker arrangements.
That means “ECOLED II right” is not a complete identification. Buyers should check:
- Left-hand or right-hand lamp
- 12 V or 24 V application
- 7-pin ASS2 or 7-pin AMP/DIN 72585 connection
- Presence of four auxiliary 2-pin outputs
- ASS2 or Superseal auxiliary connections
- End-outline marker configuration
- Exact Aspöck part number printed on the lamp or label
7-pin ASS2 and 7-pin AMP are not the same connection
The official Aspöck ECOLED II documentation shows separate 7-pin ASS2 and 7-pin AMP connector arrangements. Even though both are described as seven-pin connections, their housing, keying and pin assignments differ. A wiring harness intended for one family should not be assumed to fit or function correctly with the other.
Aspöck identifies the AMP version with the DIN 72585 connector standard in its catalogue. The ASS2 family belongs to Aspöck's modular connection system and is used with corresponding ASS connectors and harness components.
Important: never transfer a pinout from an ASS2 lamp to an AMP lamp—or from left-hand to right-hand orientation—without checking the official mounting instruction for the exact reference.
What do the additional 2-pin connections do?
Some ECOLED II versions include four auxiliary 2-pin outputs on the back of the lamp. Depending on the version and position, these connections can support functions such as tail, reverse or an SMCG-controlled side-marker circuit. Aspöck's mounting instructions identify each output and its maximum permitted current.
This distribution function can reduce separate junction requirements in a trailer-lighting installation, but only when the lamp, harness and connected marker lamps are specified as a compatible system. Review our red position lamps, white position lamps and yellow side-marker lamps when building a complete requirement.
ASS2 versus Superseal auxiliary connectors
Aspöck lists ECOLED II configurations with ASS2 auxiliary outputs as well as variants using Superseal connections. These connectors are physically different and require the matching plug, seal and wiring arrangement. The correct selection depends on the lamp reference and the existing trailer harness.
For example, the manufacturer's spare-parts catalogue lists dedicated ASS1/ASS2 female connectors in both 2-pin and 7-pin formats. It also lists separate 2-pin Superseal and 7-pin AMP female connectors. This is why a photograph of the front lens is not enough for procurement.
How to read an ECOLED II enquiry
A useful request normally includes the following information:
- Photograph the product label: capture the complete Aspöck reference without cropping any suffix.
- Confirm the side: state left or right as installed on the vehicle.
- Photograph the rear connectors: show the central connector and all auxiliary outputs.
- Record the voltage: specify the trailer or vehicle electrical system.
- List the attached lamps: include marker and end-outline lamp requirements.
- Provide the harness reference: when replacing more than the lamp, include cable and junction-box numbers.
- State quantity and destination: this helps prepare a consolidated B2B export quotation.
Common identification mistakes
Ordering by appearance alone
Several ECOLED II variants share the same general lens and housing design. The connector and suffix are often what determine compatibility.
Confusing ASS2 and AMP pin numbering
The two seven-pin systems use different connection schemes. Always use the diagram supplied for the exact connector family and lamp orientation.
Ignoring auxiliary outputs
A replacement without the required 2-pin distributor outputs can leave existing marker or reverse-light circuits without the intended connection.
Assuming left and right references are interchangeable
Aspöck documentation explains that certain ECOLED II designs can be configured through rotation and interchangeable components, but the ordered reference, connector orientation and installed accessories still need verification.
Choosing a complete Aspöck lighting system
When several components are being replaced, prepare one list covering the rear lamp, end-outline marker, position lamps, side markers, connector accessories and wiring. MSP Export can then check the references as a group rather than quoting isolated items. This is particularly useful for trailer manufacturers, fleet workshops and distributors purchasing multiple lighting references.
Explore the complete ASPÖCK collection or send us the product labels and connector photographs for part-number checking and worldwide B2B supply.
Safety and installation note
Vehicle lighting affects legal compliance and road safety. Installation must follow the exact Aspöck mounting instruction, the applicable ECE requirements and the vehicle manufacturer's electrical specifications. Disconnect power before electrical work and use qualified technicians. This guide is intended for identification and procurement, not as a substitute for the official wiring diagram.
Official technical sources
¿Necesita ayuda para encontrar la pieza correcta?
Envíenos códigos OEM, fotos de productos o referencias de marca. Nuestro equipo le ayudará a identificar la pieza correcta.